Luster Paper Standard Quality (Level 3) = 50 seconds Luster Paper High Quality (Level 2) = 1 minute 36 seconds Luster Paper Highest Quality (Level 1) = 2 minutes 21 seconds Again, one would need to be unnaturally close to the print to see them! As far as inkjet printing goes, the PRO-100 produces outstanding photo quality.p>Īn 8" x 10" file at 240ppi (shown above) was printed and timed using the settings listed below: Only in some mid-tone areas will you occasionally see a few dots. Solid blocks of color are uniform and smooth looking. This is especially true when printing on satin, luster, and glossy media. That is to say when you're printing a typical photograph, the dots of ink that make up the photo are not visible at normal viewing distance or even fairly close inspection. The Canon PRO-100 offers what we can only describe as continuous tone photo printing. Please note that you'll need specialty CD or DVD media coated for inkjet printing.Ĭanon's My Image Garden software is provided to set up and print discs. The holder is placed into a front slot on the left side of the machine. ![]() For some driver media settings, the printer will only allow the single sheet path to be used.Ībove you can see the CD holder that comes with the printer. Fine art stock, canvas, and specialty paper should be fed into the manual single sheet path. If you're using matte paper or thick media, fewer sheets should be fed in at one time. Photo papers like luster, satin, and glossy at 10.4mil are expertly handled by the PRO-100 with no misfeeds. Red River's experience thus far is that the rear tray can hold up to 50 sheets, depending on the thickness of your paper. A single page is also recommended for Fine Art papers. Manual feed - single sheet tray for heavy and specialty mediaĬanon notes that the recommended paper capacity for the rear tray is 20 pages for 4" x 6" and 5" x 7" photo media, 10 pages for letter and 8" x 10" photo media and a single page for larger sizes.Rear tray - for the majority of media you'll use.The PRO-10 has two media feed paths and a CD/DVD printing tray The PRO-100 can connect to your computer via USB 2.0, wireless network, or ethernet. Wireless connectivity button with indicator light.Consult your online manual for help with decoding the sequence should you have a problem. Errors will be identified by different sequences of blinking. Resume / Cancel button with warning light.The front control panel of the PRO-10 consists of three controls: When fully extended, the front paper tray extends 12.5" from the front of the printer. You'll want at least 10" of clearance from the back of the printer to the wall for proper operation and use of the specialty paper tray. The assembled printer is 27.2" wide, 15.2" deep, 8.5" high, and weighs 43 pounds. Once all of the inks were installed, the printer charged up and was ready to begin printing in less than five minutes. The same light blinks slowly when you're low on ink and quickly once the tank has been depleted. Once installed you will see a light on the front of the ink tank illuminate and glow steady red. It gives you a good idea of the amazing technology involved in inkjet printing and the truly small scale of a print head. Installing the head, then inks into their carriage is simple and takes about a minute.īeing able to inspect an inkjet print head up close is very interesting. A large orange plastic cover must be removed to reveal the head (see at right). The PRO-100 print head / ink cartridge assembly comes in a separate sealed bag. The system is very accurate, and you will indeed see a dry tank when it comes time to do a replacement. Rather, it starts at 100%, then records nozzle firing data sent from the printer and subtracts volume. It does not really know how much ink is physically in the tank. ![]() The onboard chip stores and reports ink level. The forward area is packed with absorbent material and holds a portion of the ink volume above the outlet to the printer head.Ĭ - Onboard chip. The rear area is open, allowing you to visually inspect the ink level. The orange cap will be removed before ink is installedī - Ink reservoir. ![]() A small amount of ink will be used in the printer setup, but you will still have plenty left to make prints and become familiar with the machine.Ī - Bottom of ink tank and ink outlet. The printer comes with a full set of CLI-42 ink cartridges.
0 Comments
Leave a Reply. |